DOREE PART 2- 1972 SQUIRE

Discussion in 'The Stable' started by andrewok1, Jul 19, 2018.

  1. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    made a lot of progress on the drivers floor panel , getting wiring troth made in floor pan hammers and heat from oxy& accet torches ,
    A LITTLE MORE TIME AND I WILL MAKE A PANEL FOR TOE KICK AREA OVER TORQUE BOX, once fit sandblasting time IMG_9782.JPG IMG_9774.JPG IMG_9775.JPG IMG_9781.JPG IMG_9784.JPG IMG_9786.JPG IMG_9789.JPG IMG_9797.JPG IMG_9800.JPG
     
    TestDummy likes this.
  2. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    IMG_9819.JPG IMG_9825.JPG IMG_9837.JPG IMG_9835.JPG OKAY ,Got the panel beat into shape meets floor profile now ,need one of those english wheels and hammer maggies / Oh WELL HAMMER TIME
    nothing better than blood sweat and (tears ,=when you hit your hand with a hammer & etc....)to help appreciating the work when its done
    cut out to finalize for floor pan size
    BACK TO SANDBLASTING , then i can begin to make the toe kick area
     
    HuevosRanchero likes this.
  3. beerbelly

    beerbelly In Maximum Overdrive SILVER MEMBER

    Messages:
    4,419
    Location:
    Portland OR
    Nice work Andrew. Did you make that air hammer tool?
     
    andrewok1 likes this.
  4. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    yes , they sell them never needed one thought , i would give it a try very helpful , Thanks BB
     
  5. cbolt

    cbolt In Overdrive SILVER MEMBER

    Messages:
    720
    Location:
    Palm Coast, FL
    You're quite the fabricating fool Andy. Nice work.
     
    andrewok1 likes this.
  6. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    THANKs Mr Cbolt , MORE again today sandblasted firewall inside Driverside .& most of the floor on drivers side . now i can make the metal over torque box IMG_9874.JPG IMG_9847.JPG IMG_9819.JPG IMG_9872.JPG IMG_9885.JPG IMG_9883.JPG IMG_9891.JPG
     
  7. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    metal made to fix drivers torque box area(toe kick)
    just needs alittle shaping yet then ready to weld in
    IMG_0025.JPG IMG_0030.JPG IMG_0029.JPG IMG_0030.JPG IMG_0033.JPG IMG_0032.JPG
     
    HuevosRanchero likes this.
  8. TestDummy

    TestDummy In Maximum Overdrive SILVER MEMBER

    Messages:
    23,405
    Location:
    C'Ville
    Nice Heavy Duty Band-Aid.
     
  9. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    they don't look the same at all :D
     
  10. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
  11. TestDummy

    TestDummy In Maximum Overdrive SILVER MEMBER

    Messages:
    23,405
    Location:
    C'Ville
    Cooler looking than hood pins.
     
    Kiwirancher and ForistellFord like this.
  12. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    Doree is going to get lots of rest over the holiday, I just need to to a break - will resume after CHRISTMAS
     
  13. TestDummy

    TestDummy In Maximum Overdrive SILVER MEMBER

    Messages:
    23,405
    Location:
    C'Ville
    Your forearms must look like Popeye's after all that hammering.

    "A-gah-gah-gah-gah-gah-gah!"
    [​IMG]
     
    ForistellFord and andrewok1 like this.
  14. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    thats better than your problem after all those short stops during crash testing . could resist,

    [​IMG]
     
    TestDummy likes this.
  15. TestDummy

    TestDummy In Maximum Overdrive SILVER MEMBER

    Messages:
    23,405
    Location:
    C'Ville
    I've reported you for hijacking this thread. For shame!!
     
    ForistellFord and andrewok1 like this.
  16. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    IMG_0069.JPG IMG_0064.JPG IMG_0066.JPG IMG_0068.JPG IMG_0070.JPG back to work on the Squire lots more cutting to finish around torque box firewall
     
  17. LSChero

    LSChero In Maximum Overdrive PLATINUM MEMBER

    Messages:
    2,562
    Location:
    Area 6 NV
    Good progress Andy!What wire are you using?Pics look like a braze weld..
     
  18. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,996
    Location:
    ocala ,florida
    Yes brazing and learning the mig, i like brazing my self that's what I learned in Vo-tech, requires sandblasting to get rid of flux ,
    s
     
  19. LSChero

    LSChero In Maximum Overdrive PLATINUM MEMBER

    Messages:
    2,562
    Location:
    Area 6 NV
    Yeh,Mig butt weld takes a little practice on 20 ga.Has to be super clean,whole bunch on small tacks,skip around let metal cool.Keep up the good
    work!Happy New year Andy!
     
  20. Basstrix

    Basstrix In Maximum Overdrive BRONZE MEMBER

    Messages:
    1,420
    Location:
    Phoenix, AZ
    I've done a little TIG brazing and read you can get bronze wire for MIG...might try that too. My TIG braze beads don't come out shiny like the ones I saw on youtube :)
     
    andrewok1 likes this.

Share This Page