DOREE PART 2- 1972 SQUIRE

Discussion in 'The Stable' started by andrewok1, Jul 19, 2018.

  1. LSChero

    LSChero In Maximum Overdrive PLATINUM MEMBER

    Messages:
    2,339
    Location:
    Area 6 NV
    I have read the 5.0 bell can be modified with early bearing and fork.
    https://www.fordmuscle.com/archives/2000/09/t5swap/index2.php
    Iam going to try to morf the mustang cable set-up to my pedals.I cant use my Zbar cause of headers interferance.May end up with some sort hydraulic system,but thats down the road..paint wars are focus currently..Lots of info out there andy,search the truck/stang forms.
    hcc4_1.jpg
     
    andrewok1 likes this.
  2. handy_andy_cv64

    handy_andy_cv64 In Maximum Overdrive SILVER MEMBER

    Messages:
    11,711
    Location:
    Seguin, TX
    This is the system on a Ranger; their MC is at this 45° angle. Ask me how I know.
     
  3. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    Thanks John
    thats a lot of good information
     
  4. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    new tool for the roost .& Squire
    sandblaster vacuum, reclaimer

    [​IMG]
     
    colnago likes this.
  5. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    turns out the transmission is FUBAR !!!!! Gears are stripped of some important Gear Matter
    will get a complete refund so the guy says ,
    1. [​IMG][​IMG]

     
  6. handy_andy_cv64

    handy_andy_cv64 In Maximum Overdrive SILVER MEMBER

    Messages:
    11,711
    Location:
    Seguin, TX
    Damn. That royally sux. But if you get a complete refund with no hidden fees, that's good.
     
    andrewok1 likes this.
  7. As Is '66

    As Is '66 2 Wheeled Mod Staff Member

    Messages:
    5,755
    Location:
    Southwest Georgia
    And we went "Ranchero-ing" again this weekend to find, secure and bring back parts...

    A good time was had by the three of us,
    Dennis
     
  8. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    we also found a bunch of hursts planted in the ground 10 or more,, main event was the the gold Ranchero ,
     
  9. Hillbilly

    Hillbilly In Maximum Overdrive

    Messages:
    6,132
    Location:
    Winchester, TN.
    I enjoyed watching you guys as ya'll walked thru the museum. There will be even more to gawk at next time you come up. Guess it confirms we be nuts to gather up all that stuff.
     
  10. As Is '66

    As Is '66 2 Wheeled Mod Staff Member

    Messages:
    5,755
    Location:
    Southwest Georgia
    I seen you looking too...
    There`s a whole lot to gawk at Now!
    Hopefully there can be more room for that stuff y`all got still to unpack...
    Remember my offer, I`ll go too...
    D
     
  11. handy_andy_cv64

    handy_andy_cv64 In Maximum Overdrive SILVER MEMBER

    Messages:
    11,711
    Location:
    Seguin, TX
    This must be where the parts Chero on the trailer comes into the picture.
     
  12. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    well i got my money back for the parts , need to locate another 5 speed trans looking into a moving and running older mustang
    , parts car ;; yes this is to ensure the a/c parts under dash & and all hardware needed to rebuild, The Squire (Doree) IS IN MY REACH, ...
    MANY NEW PARTS ENTIRE FRONT SUSPENSION IS NEWor replaced a while back with hardly any miles
     
  13. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    the Squire is back in blasting area again, GETTIN READY TO FINISH FLOORS IMG_1725.JPG IMG_1728.JPG
     
    FrenchFan likes this.
  14. handy_andy_cv64

    handy_andy_cv64 In Maximum Overdrive SILVER MEMBER

    Messages:
    11,711
    Location:
    Seguin, TX
  15. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    if can just, stay on it -2-3 hours a day, i can have the body done in the next couple months . done Haulin in Rancheros for now !!
    TRIP TO Tennesse COMING UP FOR December after Christmas,
    No trailer needed -
     
  16. handy_andy_cv64

    handy_andy_cv64 In Maximum Overdrive SILVER MEMBER

    Messages:
    11,711
    Location:
    Seguin, TX
    That's the best type to pick up!
     
  17. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    found factory bell housing, flywheel - pressure plate - clutch fork
    I am going to run factory clutch assembly and use the t-5 mounting plate on the factory bell housing ,


    [​IMG][​IMG]
     
    HuevosRanchero, LSChero and beerbelly like this.
  18. handy_andy_cv64

    handy_andy_cv64 In Maximum Overdrive SILVER MEMBER

    Messages:
    11,711
    Location:
    Seguin, TX
    *Mr. Burns* "Excellent, Smithers!"
     
    andrewok1 likes this.
  19. LSChero

    LSChero In Maximum Overdrive PLATINUM MEMBER

    Messages:
    2,339
    Location:
    Area 6 NV
    Looks like the automatic floor shift hump will work perfect!Are you going with bench seat?
    shifter_lg.jpg
     
    beerbelly and andrewok1 like this.
  20. andrewok1

    andrewok1 In Maximum Overdrive GOLD MEMBER SILVER MEMBER

    Messages:
    3,711
    Location:
    ocala ,florida
    YES,
    I was hoping to run factory high back
    thats the automatic hump
    bench seat,
     

Share This Page